The butterfly valve, as a compact, quick-opening, and low-resistance regulating valve, is widely used in industries such as water supply and drainage, HVAC, power, chemical, and paper-making. However, in practical engineering applications, improper consideration of the butterfly valve’s installation direction and spatial arrangement often leads to valve operating abnormalities, decreased sealing performance, and deviations in control accuracy. In severe cases, it can even cause system failures or frequent maintenance, resulting in unnecessary economic losses. Therefore, a correct understanding of the impact of installation orientation and spatial layout on butterfly valve performance is essential to ensure its reliable operation and extend its service life. 1. The Impact of Installation Orientation on Butterfly Valve Performance (1) Fluid Flow Direction and Its Effect on Sealing Performance For centerline butterfly valves, where the valve disc rotates around the valve shaft, the force is relatively symmetric, and the fluid flow direction has little impact on the sealing performance. Therefore, the flow direction requirement is not strict during installation. However, for eccentric butterfly valves, especially double-eccentric and triple-eccentric types, the seal design is based on the "flow-assisted compression" principle. That is, when the medium pressure comes from the specified direction, it pushes the valve disc toward the sealing seat, thereby enhancing the sealing effect. If the valve is installed in the opposite direction of the flow arrow marked by the manufacturer, the reverse fluid flow will wash the valve disc. Not only will the expected sealing effect not form, but it may also create gaps between the sealing surfaces, accelerate valve seat wear, and cause internal leakage, making it impossible to close the valve completely. Therefore, the installation of eccentric butterfly valves must strictly follow the flow direction requirements. (2) Valve Shaft Orientation and Its Effect on Opening/Closing Torque and Actuator The installation orientation of the valve shaft (horizontal or vertical) has a significant impact on the opening/closing performance, valve body stress, and actuator life. Most medium and small-sized butterfly valves are installed with the valve shaft in the horizontal position. This method facilitates the alignment of the valve body with the pipeline and the arrangement of the actuator. However, for large-diameter butterfly valves or those installed in high locations or vertical pipelines, the valve shaft is often vertical. In this position, the weight of the valve disc directly acts on the valve shaft, especially when the valve disc is in the open position, where its center of gravity deviates from the axis, creating a large eccentric torque and increasing the axial load during opening and closing. If the actuator does not account for this additional load, it may result in po...
YPFB (Yacimientos Petrolíferos Fiscales Bolivianos) as Bolivia's state-owned oil and gas company, plays a critical role in the exploration, production, and distribution of oil and natural gas across Bolivia. It has a strong commitment to quality and innovation. DERVOS VALVE is honored to have passed the qualification review and become one of contract valve suppliers of YPFB. • Supplier Qualification Requirements for YPFB Becoming a supplier for YPFB requires meeting several stringent qualifications. YPFB looks for suppliers with a proven track record of reliability, technical expertise, and product quality. This includes compliance with international industry standards and certifications,along with the ability to provide high-performance products that meet the specific needs of Bolivia’s oil and gas industry. The process also involves submitting detailed technical documentation, including certifications, safety records,and previous successful project references. • Application Process to Become a YPFB Supplier The application process to become a certified supplier for YPFB is highly competitive and rigorous. The first step is to submit an official application, followed by a review of the company’s credentials. Dervos Valve underwent this process and provided comprehensive technical documentation, including product specifications and compliance with safety standards. Our team also participated in interviews and site visits, showcasing our manufacturing capabilities and commitment to quality. DERVOS VALVE will supply a range of valves to YPFB for use in their oil and gas operations, including high-performance ball valves, gate valves, globe valves, and check valves. These products are crucial for ensuring the safety and efficiency of operations in challenging conditions. Dedicated to consistent product quality through daily operations, we ensure excellence in performance. Our ongoing commitment is providing partners with professional support and premium services, fostering mutual growth and win-win success.
To mark this milestone in Dervos Valve’s journey, we came together not just to celebrate, but to connect with the partners who have supported us along the way. This anniversary is a tribute to enduring partnerships and a sha- red vision for the future. On the occasion of Dervos Valve’s 17th anniversary, our valued partners were specially invited to visit our headquarters for in-depth, face-to-face exchanges with the team. These meaningful interactions deep- ened mutual understanding andtrust, laying a solid foundation for even stronger cooperation in the future. Accompanied by our team, the clients toured the office area and were introduced to colleagues from various departments. The interactions were relaxed and friendly, creating a warm atmosphere that further strengthened mutual understanding. Following the tour, our sales team delivered a themed presentation on “Dervos 17th Anniversary,” offering the clients a comprehensive overview of the company's development journey, core strengths, and service philosophy. We also expres- sed our heartfelt gratitude and warm welcome to our valued partners. Through this session, the clients gained a deeper understanding of Dervos, enabling us to better tailor our services to their needs. They expressed strong appreciation for Dervos’ steady growth and thanked us for inviting them to be part of this meaningful celebration. In front of the company’s cultural wall, clients took a moment to sign and leave messages, expressing their well wishes for Dervos. This moment not only reflected cultural recognition but also a genuine expression of the emotional bond and trust shared through our partnership. Next, we arrived at the highlight of the anniversary celebration— the Dervos Valve 17th Anniversary Gala Dinner, a moment of gratitude and shared celebration. We arranged a visit to the "Yu Jian Minnan" Cultural Park for our clients, where they explored the ancient architectu- ral district and experienced the traditional art of rubbings, immersing themselves in the charm and craftsman- ship of Chinese culture. In the evening, a red carpet was laid out in front of the hotel, where the Dervos team warmly welcomed guests, coming together with partners from around the world to witness this moment of honor. As the lights came on, the anniversary gala dinner officially began. The venue was decorated in a grand and festive style, with a warm and lively atmosphere. The event kicked off with a performance that blended both Eastern and Western cultures,featuring a lineup of classic foreign songs and traditional Chinese pieces, showcasing Dervos' open and inclusive brand spirit, with a global outlook. During the interactive games and lucky draw sessions, guests actively participated and enjoyed themselves, with laughter and joy filling the air. This lively atmosphere showcased the cohesion and energy of the Dervos team. As the familiar melo...
3" class300 globe valve is made according to BS1873 standard. The valve body is made of Monel. Its connection mode is RF. And it has hand wheel operation mode.
Payment:
30% when order confirmed, 70% before shipmentProduct Origin:
ChinaColor:
CustomizationShipping Port:
Shanghai, ChinaLead Time:
30~60 days Ex Works after order confirmationMaterial:
MonelMethod of Operation:
Hand WheelProduct Description
|
Type |
Globe Valve |
|
Size |
3" |
|
Pressure |
Class300 |
|
Connection |
RF |
|
Operation |
Hand Wheel |
|
Body Material |
Monel |
|
Design Norm |
BS1873 |
|
Face to Face Dimensions |
ASME B16.10 |
|
Flange Ends Dimensions |
ASME B16.5 |
|
Pressure Test |
API STD. 598 |
|
Applicable Medium |
Acid |
Features
1. The HF acid valve adopts high-quality corrosion-resistant materials such as fluoroplastics, stainless steel, alloy steel, ceramics, etc.
2. It has strong acid and alkali resistance, making it suitable for long-term operation in highly concentrated and high-temperature corrosive media.
Technical Drawing
Product Details
Available Modifications for Dervos Valves
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
24" 300LB check valve is made according to API 594 standard. The valve body is made of A216 WCB+STL. It has the structural characteristics of double plate and built-in type. Its connection mode is wafer type.
The dual disc wafer check valve is designed as per API 594 and tested per API 598. The bronze non return valve is applicable for sea water. Quick Detail Type Check Valve Size 6'' DesignPressure Class 150 Construction Dual Plate Type, With Retainer Connection Wafer Type Design & Manufacture API 594 End to End ASME B16.10 Connection ASME B16.5 Pressure & Temp ASME B16.34 Test & Inspection API 598 Body Material Aluminum Bronze C95800 Trim Material Aluminum Bronze C95800 Media W.O.G. Dervos Inspection after Valve Assembly Valve quality is one of perspectives we care about most. In Dervos, quality control starts from raw material, machining, assembly to pre-shipment inspection. After assembly, the quality checking team will do visual checking, dimension checking, hydraulic testing and air testing. Every order must pass the test per inspection standards. Otherwise our quality checking team will not release the shipment. Inspection Reports Documents can be used to prove how we control valve quality. Along with every order, Dervos will provide clients with an inspection report & a 3.1 mill test report for free. In Dervos inspection report, you will see the actual results of dimension checking and pressure testing along with painting and packing picture. All these info are shown through data and clear pictures. In 3.1 mill test report, we will show you the chemical composition, mechanical property and heat number for valve body, bonnet, stem, disc and so on.
4x3" 150LB floating ball valve is made according to API 6D standard. The valve body is made of A182 F51. It has the structural characteristics of two piece, floating ball, reduced diameter, anti-fire, anti-static, anti-flying valve stem, bidirectional, with locking device. Its connection mode is RF. And it has lever operation mode.
The stainless steel CF8 non return valve features in non slam type disc, ANSI 150 flange end, and full port design. Quick Detail Type Non Return Valve ( Check Valve) Size 8'' DesignPressure Class 150 Construction Non Slam Type Connection RF Flange Design & Manufacture ASME B16.34 End to End ASME B16.10 Connection ASME B16.5 Pressure & Temp ASME B16.34 Test & Inspection API 598 Body Material A351 CF8 Trim Material SS304 Media W.O.G. Available Modifications for Dervos Valves -Valve Pressure -Valve Size -Reduced Bore & Full Bore -Body & Trim Material (Disc, Seat, Pin, Spring) -End Connection (Flange, BW, SW, Thread, Wafer, Lug) -Available Operation (Bare Stem, With Actuators) -Available Counterweight -Available Cylinder -Customizing Coating -Customizing Packaging Related Knowledge What is non-slam check valve? Water hammer is a hydraulic phenomenon that undergoes an abrupt change in its rate of flow and are caused by sudden shutting or slamming. Water hammer will reduce process efficiency, cause valve damage, gasket joint leaks and other problems. The non-slam check valve is designed to reduce water hammer. An internal spring can prevent the disc from slamming close.The design of a non-slam check valve could eliminate pressure flutuations, vibration and damges. Plus, the disc and spring experience minimal wear over time, which will largely extend the service lives of non-slam check compared to swing check valve.
6" 600LB check valve is made according to API 594 standard. The valve body is made of A216 WCB+316. It has the structural characteristics of dual plate and wafer type. Its connection mode is wafer.
The 16 inch triple offset butterfly valve is designed with metal seat, stainless steel CF8M body, disc and stem. The fully lugged butterfly valve with gearbox has Class 150 design pressure as per API 609. Design Feature 1. Small volume, light weight, simple structure 2. Multi-layer metal seated/fully metal seated 3. Firesafe design 4. Anti-blowout stem 5. Small torque value for operating easily 6. Reliable sealing and could meet zero leakage requirement 7. With function of regulating flow 8. Triple eccentric design for minimized wear of sealing face Quick Detail Type Butterfly Valve Size 16'' Pressure ANS 150 Structure Triple Eccentric, Triple Offset, Metal Seated Connection Type Lug Type Operation Gearbox Operated Design Code API 609 Face to Face ASME B16.10 End Connection ASME B16.5 Test & Inspection API 598 Body Material A351 CF8M Temperature Range -29℃~+425℃ Application Water, Oil, Gas Material No Part Name Carbon steel to ASTM Alloy steel to ASTM Stainless steel to ASTM WCB WC6 WC9 C5 CF8 CF8M CF3 CF3M 1 Body A216 WCB A217 WC6 A217 WC9 A217 C5 A351 CF8 A351 CF8M A351 CF3 A351 CF3M 2 Below Axle Bush PTFE or Stainless Steel and Graphite Spiral Wound 3 Stem A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L 4 Seat Ring F6 Stellite 6 Stellite 6 Stellite 6 A182 F304 A182 F316 A182 F304L A182 F316L 5 Butterfly Plate A216 WCB A217 WC6 A217 WC9 A217 C5 A351 CF8 A351 CF8M A351 CF3 A351 CF3M 6 Lock Ring A105 A182 F22 A182 F22 A182 F22 A182 F304 A182 F316 A182 F304L A182 F316L 7 Pin Carbon Steel or Alloy Steel 8 Screw Carbon Steel or Alloy Steel 9 Top Axle Bush PTFE or Stainless Steel and Graphite Spiral Wound 10 Packing Graphite+SS304 11 Bolt A193 B7 A193 B7 A193 B7 A193 B7 A193 B8 A193 B8 A193 B8 A193 B8 12 Nut A194 2H A194 2H A194 2H A194 2H A194 Gr.8 A194 Gr.8 A194 Gr.8 A194 Gr.8 13 Bolt A193 B7 A193 B7 A193 B7 A193 B7 A193 B8 A193 B8 A193 B8 A193 B8 14 Nut A194 2H A194 2H A194 2H A194 2H A194 Gr.8 A194 Gr.8 A194 Gr.8 A194 Gr.8 15 Yoke A216 WCB A217 WC6 A217 WC9 A217 C5 A351 CF8 A351 CF8M A351 CF3 A351 CF3M 16 Gland A182 F6 A182 F304 A182 F304 A182 F304 A182 F304 A182 F316 A182 F304L A182 F316L
10" 300LB Y Type Strainer is made according to ASME B16.34 standard. The valve body is made of ASTM A216 WCB. It has the structural characteristics of Y-shaped and bolt cover. Its connection mode is RF.
1" 300LB gate valve is made according to API 602 and ASME B16.34 standard. The valve body is made of A350-LF2. It has the structural characteristics of bolt cover, exposed rod, OS&Y, reduced diameter. Its connection mode is RF integral flange. And it has polished rod operation mode.
The 3 way plug valve is made of WCB body and stainless steel trim as per API 599. The plug valve that could connect any two ports together is applicable for natural gas service, water, oil and so on. Quick Detail Type Plug Valve Size 4'' DesignPressure 150LB Construction Three Way Type Plug Valve ConnectionType Flange Connection Operation Lever/Wrench Design Code API 599 Face to Face ASME B16.10 End Connection ASME B16.5 Pressure & Temp ASME B16.34 Test & Inspection API 598 Body Material A216 WCB TemperatureRange -29℃~+425℃ Application WOG Related Knowledge What are types of plug valves? Lubricated Plug Valve The plug gets lubricated by injecting sealant through injection fitting. The lubricant make sure the smooth movement and prevent the corrosion of plug. Usually, the seat of lubricated plug valve is metal, thus they can withstand higher temperature, available in larger size and higher pressure. Non-Lubricated Plug Valve A non-metallic sleeve or liner is installed in the body cavity of the plug valve. This sleeve reduce the fricion beween plug and body. Meanwhile it prevents the corrosion of plug. Due to non-metallice sleeve, the non-lubricated plug valve cannot be used in high temperature condition. Multiway Plug Valve The multiway plug valve is used for diverting flow in transfer lines. The multiway plug valves we often see are 3 way plug valve or 4 way plug valve. Dervos Packaging Based on sufficient experience, we have developed complete packing specifications and procedures to ensure clear and safe transportation so that you can receive good and sound products. And this is also an important factor that we earn good reputation from our customers.
2" 150LB globe valve is made according to BS1873 standard. The valve body is made of A216 WCB. It has the structural characteristics of bolt cover, rising stem, OS&Y and body valve seat. Its connection mode is RF. And it has hand wheel operation mode.
The DN65 PN16 angle type globe valve is made of cast steel 1.0619 body and ss304 trim material, with rising stem, handwheel, RF flange. Quick Detail Type Globe Valve Norminal Size DN 65 NorminalPressure PN 16 Construction Angle Pattern, BB ConnectionType Flanged Operation Handwheel Design Code DIN 3356 Face to Face EN 558 Connection EN1092 Test & Inspection EN12266 Body Material GS-C25 (1.0619) ApplicableTemp -29℃~+425℃ Application WOG Related Knowledge Why use an angle type globe valve? Angle globe valve turns the flow direction by 90 degrees without using an elbow or the extra pipe weld, which reduce the number of joints on the pipeline, save the installation time, and reduce the pressure drop & flow resistance. The angle pattern globe valve are used for application with periods of pulsating flow, since they are able to handle slugging effect. Our Main Product Range As an experienced supplier and vendor of industrial valves, Dervos supply cast steel valve, forged steel valve, cast iron valve, stainless steel valve, bronze valve, brass valve and alloy steel valve and so on, suitable for sea water, water, oil, and gas application.
16" CL150 single disc swing check valve is made according to API 594 standard. The valve body is made of ASTM A351 CF8M. It has the structural characteristics of single disc, swing style. Its connection mode is wafer.
Copyright © 2015-2025 DERVOS VALVE CO.,LTD.All Rights Reserved Blog / Sitemap / XML / Privacy Policy
