English

English

Get a Quote
Products

Hot Products

Company News

Pressure Seal Bonnet vs Bolted Bonnet Gate Valves: Selection for High-Pressure Service
Pressure Seal Bonnet vs Bolted Bonnet Gate Valves: Selection for High-Pressure Service
2026-11-20

A pressure-seal bonnet is usually the stronger candidate for very high-pressure, high-temperature service because internal pressure increases the sealing load at the body-bonnet joint. A bolted bonnet relies primarily on bolt preload to compress its gasket and is often simpler to inspect and disassemble.   That does not create a universal pressure-class cutoff. A Class 600 valve may use a pressure seal, while a bolted-bonnet design may be available at a higher class. The correct choice depends on the applicable pressure-temperature rating, valve size, material, thermal cycles, start-up conditions, maintenance plan, and the manufacturer’s qualified design.   Quick Selection Answer   Choose a pressure-seal bonnet when the service combines high pressure with high temperature, repeated thermal loading, or a critical external-leakage consequence, and the plant can support its more specialized maintenance procedure.   Choose a bolted bonnet when the approved valve design satisfies the full pressure-temperature envelope and familiar disassembly, gasket replacement, and general maintenance access have greater value.   Do not use the bonnet style to decide the valve function. Gate, globe, and check valves can all be made with pressure-seal constructions, but they perform different jobs in the system.   How Does a Bolted Bonnet Work?   In a bolted-bonnet valve, a flanged joint connects the bonnet to the body. Studs or bolts apply the initial clamping force, compressing a gasket between the mating faces. The bolting, flange geometry, gasket, surface finish, assembly method, and temperature all affect joint integrity.   As internal pressure rises, pressure-generated forces tend to separate the body and bonnet. The joint must retain enough gasket compression after pressure, temperature change, bolt relaxation, and thermal expansion are considered. Correct tightening sequence and controlled preload therefore matter.   The main practical advantage is familiarity. Maintenance teams can see and access the external bolting, and the disassembly sequence is generally straightforward. However, the joint may become large and heavily bolted as pressure, size, and design load increase.   How Does a Pressure-Seal Bonnet Work?   A pressure-seal bonnet uses an internal gasket and a retaining system rather than a conventional large external body-bonnet flange. Exact details vary, but common designs use a bonnet or cover, pressure-seal gasket, spacer or thrust ring, and segmented retaining ring inside the body neck.   Process pressure acts on the bonnet assembly and forces the sealing elements against their contact surfaces. As pressure increases, the body-bonnet sealing load also increases. This is why the design is described as self-energizing or pressure assisted.   Self-energizing does not mean self-assembling. At zero or low pressure, the process has not yet created its full sealing force. The initia...

Check Valve Cracking Pressure: How to Select the Opening Threshold for Low-Flow and Pump Service
Check Valve Cracking Pressure: How to Select the Opening Threshold for Low-Flow and Pump Service
2026-11-13

A check valve can begin to pass fluid and still be far from a stable open position. Check valve cracking pressure is therefore the threshold for first detectable flow, not the full-open pressure drop or proof of reliable minimum-flow operation.   For low-flow and pump service, the opening threshold is acceptable only when the system can exceed it in the worst forward-flow case. The selection must then pass three separate checks: stable valve travel at minimum flow, acceptable pressure loss at normal and maximum flow, and timely closure when the pump stops.   Start with the Worst Available Differential Pressure   Parker defines cracking pressure as the upstream pressure at which detectable flow is measured, while Swagelok notes that first flow does not mean the valve is fully open. The relevant system value is not pump discharge pressure alone, but the pressure difference across the valve when it must open.   For an initial screen: Available opening ΔP = minimum upstream pressure at the valve − maximum downstream pressure at the valve If the pressures come from remote points, correct them for elevation and line losses. Evaluate the least favorable credible case, such as a variable-speed pump starting at low speed or a standby pump opening against a live common header.   The maximum guaranteed cracking pressure of the offered valve should be below this available ΔP, with an engineering allowance for manufacturing tolerance, temperature, orientation, deposits and measurement uncertainty. There is no defensible universal allowance. A nominal value alone is insufficient because catalog cracking pressure may be specified as a range, and a valve left idle may initially require a higher differential than it does after cycling.   Low Cracking Pressure Does Not Solve Low-Flow Instability   After the closure member lifts, more differential pressure and flow force are needed for stable travel. An oversized valve may crack open but hover near the seat because velocity is too low, causing clicking, flutter, impact and accelerated wear.   Swagelok’s service guidance identifies excessive spring cracking pressure and excessive valve size as possible causes of chatter near the threshold. Size from the operating envelope rather than automatically matching the pipe diameter.   Ask the supplier to evaluate three points for the exact size, spring and trim: Operating point Required evidence Minimum continuous flow Stable-open position, minimum stable flow or velocity, and corresponding ΔP Normal flow Model-specific pressure-drop curve or validated flow coefficient Maximum flow Peak ΔP, velocity limits, erosion risk and acceptable travel   Cracking pressure answers “When does motion begin?” The flow curve and stable-flow limit answer “Will the valve remain open without damaging itself?”   Pump Opening and Pump Shutdown Are Different Design Cases   At s...

Should You Use a Ball Valve for Throttling? Seat Damage, Cavitation and Better Alternatives
Should You Use a Ball Valve for Throttling? Seat Damage, Cavitation and Better Alternatives
2026-11-05

A standard on-off ball valve should not be the default choice for continuous throttling. It can restrict flow, but that does not make it a control valve. Holding it partly open can expose the seat to a concentrated high-velocity jet, produce unstable control and, in liquid service, create cavitation. Brief restriction during start-up or shutdown may be acceptable if the manufacturer permits it. Regular modulation requires a valve designed and sized for that duty.   A Part-Open Ball Puts the Seat in the Flow Path   When a standard ball valve is fully open, the bore provides a relatively straight flow path. As the ball rotates toward closed, the opening becomes a narrow, changing shape. Velocity rises through this restriction, and the emerging jet can pass close to the downstream seat edge and body cavity.   That matters because the seat performs the shutoff function. A soft seat may deform, cut or erode under high velocity, heat and entrained solids. A metal seat may tolerate harsher conditions, but hardness alone does not provide a suitable control characteristic or prevent local erosion. Damage often appears later as increased shutoff leakage, even though the valve still moves normally.   Control quality is another limitation. A conventional full-port ball may pass a large increase in flow over a small change in travel once it begins to open. The actuator can therefore hunt around a narrow angle instead of positioning smoothly across a useful range. A positioner cannot correct an unsuitable valve characteristic.   Cavitation Depends on the Local Pressure, Not Just Line Pressure   Cavitation is possible when liquid accelerates through the restriction and its local pressure falls below the liquid's vapour pressure. Vapour bubbles then form. If pressure recovers above vapour pressure downstream, the bubbles collapse and release damaging energy near the valve or downstream pipe.   Ball valves are generally high-recovery valves: much of the pressure lost at the narrowest flow area is recovered downstream. That means the minimum internal pressure can be considerably lower than the measured outlet pressure. A moderate-looking inlet-to-outlet pressure drop may therefore hide a more severe pressure dip inside the valve.   Noise resembling gravel, vibration and rough pitting are warning signs, but sound alone is not a design method. The evaluation needs minimum, normal and maximum flow; upstream and downstream pressure at each case; fluid temperature and vapour pressure; density; solids content; valve size; and the manufacturer's pressure-recovery and sizing data. If downstream pressure remains below vapour pressure, the condition is flashing rather than cavitation and requires a different damage assessment.     A Ball Valve Can Throttle When It Is a Control Valve   A V-port or segmented ball introduces a shaped opening that gives a more predictable relationship between travel and flow. Correctly sele...

Flat Gate Valve
加载中...

3" 1500LB Flat Gate Valve, RTJ Connection, Body A995 4A, API6D

3" 1500LB flat gate valve is made according to API6D standard. The valve body is made of ASTM A995 4A. It has the structural characteristics of BB, OS&Y, with diversion holes. Its connection mode is RTJ. And it has hand wheel operation mode.

  • Payment:

    30% when order confirmed, 70% before shipment
  • Product Origin:

    China
  • Color:

    Customization
  • Shipping Port:

    Shanghai, China
  • Lead Time:

    30~60 days Ex Works after order confirmation
  • Material:

    ASTM A995 4A
  • Method of Operation:

    Hand Wheel
Inquiry now
Product Detail

Product Description

Type

Flat Gate Valve

Size

3"

Pressure

1500LB

Connection

RTJ

Operation

Hand Wheel

Body Material

ASTM A995 4A

Design Norm

API 6D

End to End

API 6D

End connection

ASME B16.5

Test & Inspection Code

API 6D

Temperature

-29 ~ 120°C

Applicable Medium

Water, Oil and Gas

Features

1. Reliable operation, easy maintenance, good economy, suitable for large-scale application and promotion;

2. Low fluid resistance, low pressure loss, beneficial for energy conservation and emission reduction.

Technical Drawing

Dimension Checking

Pressure Testing


Nameplate & Packing

Inspection report

Leave A Message

If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Related Products
Carbon Steel Slab Gate Valve
Through Conduit Slab Gate Valve DN200 PN64 Flanged

The through conduit slab gate valve, designed as per DIN standard, has the diversion hole for pipeline cleaning. The PN64 parallel disc gate valve is made of carbon steel with RF flange and handwheel. Quick Detail Type Parallel Slab Gate Valve Nominal Diameter DN 200 Nominal Pressure PN 64 Construction Parallel Slabe Gate Valve, With Diversion Hole, Bolted Bonnet, Resilient Seat Connection Flange Operation Handwheel Operation Body Material Carbon Steel Medium Water, Oil and Gas Origin China Design Feature 1.Parellel disc 2.Soft seat and metal seat for choices 3.Full bore design for pigging and less pressure drop 4.Firesafe design 5.Self relieving function 6.Grease fitting for seat and stem 7.Double block and bleed capability 8.With vent and drain port 9.Tight sealing performance  Material Part Name Material Body & Bonnet A216 WCB, CF8, CF8M, CF3, CF3M Wedge Alloy Steel (face harden treated), Stainless Steel (with Co overlay) Stem Alloy Steel (face erosion-resistant treated) Seat Alloy Steel (face harden treated, beset F plastic), Steel (with Co overlay, best F plastic) Packing PTFE O-Ring NBR, FEP Sealing Grease  

Through Conduit Gate Valve
Through Conduit Expanding Gate Valve 18 Inch 600LB API6D

The API 6D through conduit gate valve is designed with double expanding wedges, metal to metal seat and diversion hole for pigging. The valve has good performance on sealing, less flow resistance and is suitable for application with some solids or particles. Quick Detail   Type Gate Valve Size 18'' Design Pressure ANSI 600 Construction Double Expanding Wedges, Fully Metal Seat, With Diversion Hole ConnectionType RTJ Flange OperationType Gearbox Operated Body Material WCB WedgeMaterial A105+STL+ENP StemMaterial 17-4PH SeatMaterial A105+STL+ENP Design Code API 6D Face to Face Dimension ASME B16.10 End Connection ASME B16.5 Pressure & Temp ASME B16.34 Medium Water, Oil and Gas Origin China

DN100 A516 Through Conduit Slab Gate Valve with Drain Valve
DN100 A516 Through Conduit Slab Gate Valve with Drain Valve

The DN100 through conduit slate gate valve is made according to EN558.It is ideal for pipeline applications requiring pigging capability.

Flat Gate Valves
DN250 PN100 High-Pressure Flat Gate Valve with Drain Valve

It is a Carbon Steel full bore flat gatevalve with parallel wedge, DN250 PN100, made from LCC, one kind of low-temp carbon steel, which makes this valve capable to handle extreme working conditions.

Gate Valve
API 6D Through Conduit Gate Valve Soft Seated 20 Inch 600LB

The API 6D through conduit gate valve is designed with 600 LB flange and gearbox connection. Made of carbon steel WCB, the 20 inch gate valve has soft seat design without diversion hole.

Gate Valve
10''/ 12''/ 24'' 600LB Flat Gate Valve API6D RF

10’’ ~ 24’’ 600LB gate valve is made according to API 6D standard. The valve body is made of A516 Gr70. It has the structural characteristics of parallel gate. The operation mode is gear operation.

Leave a message

    If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

about

contact