English

English

Get a Quote
Products

Hot Products

Company News

Pressure Seal Bonnet vs Bolted Bonnet Gate Valves: Selection for High-Pressure Service
Pressure Seal Bonnet vs Bolted Bonnet Gate Valves: Selection for High-Pressure Service
2026-11-20

A pressure-seal bonnet is usually the stronger candidate for very high-pressure, high-temperature service because internal pressure increases the sealing load at the body-bonnet joint. A bolted bonnet relies primarily on bolt preload to compress its gasket and is often simpler to inspect and disassemble.   That does not create a universal pressure-class cutoff. A Class 600 valve may use a pressure seal, while a bolted-bonnet design may be available at a higher class. The correct choice depends on the applicable pressure-temperature rating, valve size, material, thermal cycles, start-up conditions, maintenance plan, and the manufacturer’s qualified design.   Quick Selection Answer   Choose a pressure-seal bonnet when the service combines high pressure with high temperature, repeated thermal loading, or a critical external-leakage consequence, and the plant can support its more specialized maintenance procedure.   Choose a bolted bonnet when the approved valve design satisfies the full pressure-temperature envelope and familiar disassembly, gasket replacement, and general maintenance access have greater value.   Do not use the bonnet style to decide the valve function. Gate, globe, and check valves can all be made with pressure-seal constructions, but they perform different jobs in the system.   How Does a Bolted Bonnet Work?   In a bolted-bonnet valve, a flanged joint connects the bonnet to the body. Studs or bolts apply the initial clamping force, compressing a gasket between the mating faces. The bolting, flange geometry, gasket, surface finish, assembly method, and temperature all affect joint integrity.   As internal pressure rises, pressure-generated forces tend to separate the body and bonnet. The joint must retain enough gasket compression after pressure, temperature change, bolt relaxation, and thermal expansion are considered. Correct tightening sequence and controlled preload therefore matter.   The main practical advantage is familiarity. Maintenance teams can see and access the external bolting, and the disassembly sequence is generally straightforward. However, the joint may become large and heavily bolted as pressure, size, and design load increase.   How Does a Pressure-Seal Bonnet Work?   A pressure-seal bonnet uses an internal gasket and a retaining system rather than a conventional large external body-bonnet flange. Exact details vary, but common designs use a bonnet or cover, pressure-seal gasket, spacer or thrust ring, and segmented retaining ring inside the body neck.   Process pressure acts on the bonnet assembly and forces the sealing elements against their contact surfaces. As pressure increases, the body-bonnet sealing load also increases. This is why the design is described as self-energizing or pressure assisted.   Self-energizing does not mean self-assembling. At zero or low pressure, the process has not yet created its full sealing force. The initia...

Check Valve Cracking Pressure: How to Select the Opening Threshold for Low-Flow and Pump Service
Check Valve Cracking Pressure: How to Select the Opening Threshold for Low-Flow and Pump Service
2026-11-13

A check valve can begin to pass fluid and still be far from a stable open position. Check valve cracking pressure is therefore the threshold for first detectable flow, not the full-open pressure drop or proof of reliable minimum-flow operation.   For low-flow and pump service, the opening threshold is acceptable only when the system can exceed it in the worst forward-flow case. The selection must then pass three separate checks: stable valve travel at minimum flow, acceptable pressure loss at normal and maximum flow, and timely closure when the pump stops.   Start with the Worst Available Differential Pressure   Parker defines cracking pressure as the upstream pressure at which detectable flow is measured, while Swagelok notes that first flow does not mean the valve is fully open. The relevant system value is not pump discharge pressure alone, but the pressure difference across the valve when it must open.   For an initial screen: Available opening ΔP = minimum upstream pressure at the valve − maximum downstream pressure at the valve If the pressures come from remote points, correct them for elevation and line losses. Evaluate the least favorable credible case, such as a variable-speed pump starting at low speed or a standby pump opening against a live common header.   The maximum guaranteed cracking pressure of the offered valve should be below this available ΔP, with an engineering allowance for manufacturing tolerance, temperature, orientation, deposits and measurement uncertainty. There is no defensible universal allowance. A nominal value alone is insufficient because catalog cracking pressure may be specified as a range, and a valve left idle may initially require a higher differential than it does after cycling.   Low Cracking Pressure Does Not Solve Low-Flow Instability   After the closure member lifts, more differential pressure and flow force are needed for stable travel. An oversized valve may crack open but hover near the seat because velocity is too low, causing clicking, flutter, impact and accelerated wear.   Swagelok’s service guidance identifies excessive spring cracking pressure and excessive valve size as possible causes of chatter near the threshold. Size from the operating envelope rather than automatically matching the pipe diameter.   Ask the supplier to evaluate three points for the exact size, spring and trim: Operating point Required evidence Minimum continuous flow Stable-open position, minimum stable flow or velocity, and corresponding ΔP Normal flow Model-specific pressure-drop curve or validated flow coefficient Maximum flow Peak ΔP, velocity limits, erosion risk and acceptable travel   Cracking pressure answers “When does motion begin?” The flow curve and stable-flow limit answer “Will the valve remain open without damaging itself?”   Pump Opening and Pump Shutdown Are Different Design Cases   At s...

Should You Use a Ball Valve for Throttling? Seat Damage, Cavitation and Better Alternatives
Should You Use a Ball Valve for Throttling? Seat Damage, Cavitation and Better Alternatives
2026-11-05

A standard on-off ball valve should not be the default choice for continuous throttling. It can restrict flow, but that does not make it a control valve. Holding it partly open can expose the seat to a concentrated high-velocity jet, produce unstable control and, in liquid service, create cavitation. Brief restriction during start-up or shutdown may be acceptable if the manufacturer permits it. Regular modulation requires a valve designed and sized for that duty.   A Part-Open Ball Puts the Seat in the Flow Path   When a standard ball valve is fully open, the bore provides a relatively straight flow path. As the ball rotates toward closed, the opening becomes a narrow, changing shape. Velocity rises through this restriction, and the emerging jet can pass close to the downstream seat edge and body cavity.   That matters because the seat performs the shutoff function. A soft seat may deform, cut or erode under high velocity, heat and entrained solids. A metal seat may tolerate harsher conditions, but hardness alone does not provide a suitable control characteristic or prevent local erosion. Damage often appears later as increased shutoff leakage, even though the valve still moves normally.   Control quality is another limitation. A conventional full-port ball may pass a large increase in flow over a small change in travel once it begins to open. The actuator can therefore hunt around a narrow angle instead of positioning smoothly across a useful range. A positioner cannot correct an unsuitable valve characteristic.   Cavitation Depends on the Local Pressure, Not Just Line Pressure   Cavitation is possible when liquid accelerates through the restriction and its local pressure falls below the liquid's vapour pressure. Vapour bubbles then form. If pressure recovers above vapour pressure downstream, the bubbles collapse and release damaging energy near the valve or downstream pipe.   Ball valves are generally high-recovery valves: much of the pressure lost at the narrowest flow area is recovered downstream. That means the minimum internal pressure can be considerably lower than the measured outlet pressure. A moderate-looking inlet-to-outlet pressure drop may therefore hide a more severe pressure dip inside the valve.   Noise resembling gravel, vibration and rough pitting are warning signs, but sound alone is not a design method. The evaluation needs minimum, normal and maximum flow; upstream and downstream pressure at each case; fluid temperature and vapour pressure; density; solids content; valve size; and the manufacturer's pressure-recovery and sizing data. If downstream pressure remains below vapour pressure, the condition is flashing rather than cavitation and requires a different damage assessment.     A Ball Valve Can Throttle When It Is a Control Valve   A V-port or segmented ball introduces a shaped opening that gives a more predictable relationship between travel and flow. Correctly sele...

GATE VALVE

A gate valve, also known as a sluice valve, is a valve that opens by lifting a barrier (gate) out of the path of the fluid.” The main function of a gate valve is to cut off the medium. Dervos has been supplying gate valves for more than 10 years, from API 600 wedge gate valve, API 6D through conduit gate valve, API 6A wellhead gate valve to knife gate valve, pressure seal gate valve, bellow seal gate valve, expanding gate valve, carbon steel gate valve, stainless steel gate valve to cast iron gate valve and etc.


Gate Valve Category

  • #
    Steel Gate Valve
    Available in Cast Steel, Forged Steel, Alloy Steel bodies with bolted or flanged bonnet, featuring:
    · Size range: 2'' to 48'' (DN50 to DN1200)
    · Pressure range: Class 150 to 2500 (PN16 to PN420)
  • #
    Ductile Iron Gate Valve
    Body with bolted or flanged bonnet, featuring:
    · Size range: 2'' to 36'' (DN50 to DN900)
    · Pressure range: Class 150 to 300 (PN16 to PN40)
  • #
    Cast Iron Gate Valve
    Body with bolted or flanged bonnet, featuring:
    · Size range: 2'' to 36'' (DN50 to DN900)
    · Pressure range: Class 125 to 150 (PN10 to PN16)
  • #
    Knife Gate Valve
    Wedge-type or sharp-edged gate, featuring:
    · Size range: 2'' to 48'' (DN50 to DN1200)
    · Pressure range: Class 150 to 300 (PN16 to PN50)
  • #
    Through Conduit Gate Valve
    Full bore design for slurry and viscous media, featuring:
    · Size range: 4'' to 48'' (DN100 to DN1200)
    · Pressure range: Class 150 to 300 (PN16 to PN50)
  • #
    Pressure Seal Gate Valve
    Bolted bonnet with pressure seal design, featuring:
    · Size range: 4'' to 48'' (DN100 to DN1200)
    · Pressure range: Class 600 to 2500 (PN100 to PN420)
  • #
    Cryogenic Gate Valve
    Low-temperature design for -196°C to -50°C, featuring:
    · Size range: 2'' to 36'' (DN50 to DN900)
    · Pressure range: Class 150 to 900 (PN16 to PN160)
  • #
    Wellhead Gate Valve
    API 6A compliant, for oil & gas applications, featuring:
    · Size range: 2'' to 24'' (DN50 to DN600)
    · Pressure range: Class 5000 to 20000 psi
  •  


Size, Pressure and Material Range of Gate Valves

 

Size: from 2'' to 72'' (from DN 50 to DN 1800)

Pressure: from Class 150 to Class 2500 (from PN 10 to PN 420)

Material: Carbon Steel, Stainless Steel, Alloy Steel, Duplex Stainless Steel, Super Duplex, Nickel Alloy, Cast Iron, Ductile Iron


Features of Gate Valves

 

1.Low Fluid Resistance for Smooth Flow

The straight-through flow path ensures minimal pressure loss, making gate valves suitable for large-diameter pipelines and long-distance fluid transmission.

 

2.Reliable Shut-Off Performance

With a wedge, parallel, or flexible gate design, gate valves deliver tight sealing when fully closed, ensuring dependable isolation even under high pressure.

 

3.Simple Open/Close Mechanism

Operated by turning the handwheel or actuator to raise or lower the gate, the valve achieves complete separation of the flow with clear open and close positions.

 

4.Full-Open Design with No Flow Obstruction

When fully opened, the gate retracts completely out of the flow passage, providing an unobstructed full-bore design ideal for pigging and minimal erosion.

 

5.Automation-Compatible

Gate valves can be equipped with electric, pneumatic, or hydraulic actuators to support remote control and integration into automated pipeline systems.

 

6.Multiple Operation Modes Available

Electric actuator gate valve, gear-operated gate valve, pneumatic gate valve, hydraulic operated gate valve, manual gate valve, rising stem and non-rising stem configurations, etc.

 

7.Various Connection Ends Available

Flanged ends connection, threaded connection, NPT threaded gate valve, butt-weld end, socket-weld end, wafer-type connection, lug-type connection, etc.


Gate Valve Application

 

1.Oil and Gas Industry

Gate valves for the oil and gas industry, suitable for crude oil and natural gas transmission pipelines, wellhead isolation, block valve stations, and long-distance trunk lines.

 

2.Chemical and Pharmaceutical Industry

Suitable for corrosive, high-temperature, or high-pressure media, and widely used in process pipelines, storage tanks, and chemical isolation systems.

 

3.Power Industry

Ideal for high-temperature and high-pressure steam pipelines, boiler feed-water systems, cooling water networks, and auxiliary power plant equipment.

 

4.Water Treatment and Environmental Protection Projects

Suitable for municipal water supply systems, wastewater treatment, desalination plants, and large-diameter pipeline isolation in environmental engineering.

 

5.Building and HVAC Systems

Used in building water supply networks, fire-fighting systems, heating loops, and central air-conditioning pipeline isolation.

 


 
Gate Valve Application Cases
DERVOS supports ECOFUEL’s innovative clean-energy project in Canada, supplying 136 sets of high-quality valves to enable sustainable diesel production from solid waste. ECOFUEL recognizes DERVOS for its reliability, customization capability, and outstanding performance in this landmark green-technology initiative. READ MORE

Gate Valve FAQS

 

1. What is a gate valve used for?

A gate valve is used for fully opening or fully shutting off fluid flow in pipelines.

 

2.Gate valve price DN100 PN16?

Prices vary by material and standard — request a quotation for exact pricing.

 

3.Rising stem gate valve vs non-rising stem gate valve?

One-line answer: Rising stem shows position; non-rising stem saves space — full types available.     

                                  

4.Which is better for my pipeline: cast steel or forged steel gate valves?

Forged steel is ideal for smaller, high-pressure valves, while cast steel suits larger diameters and moderate pressures. Explore our product range to find the right choice.                                                     

 

5.What types of gate valves are recommended for water pipelines with different pressure ratings?

We provide DN50–DN1200 gate valves with PN10–PN40 ratings suitable for reliable water pipeline isolation. Detailed dimensions and models are available online.         

    

6.Which gate valves can be used safely in oil and gas pipelines?

Our API-compliant gate valves ensure safe operation under high-pressure oil and gas conditions. Visit our site to check materials, sizes, and pressure ratings.

 

GATE VALVE


Tags

api 600 gate valve | api 6d through conduit gate valve | api 6a wellhead gate valve | wedge gate valve | knife gate valve | pressure seal gate valve | bellow seal gate valve | expanding gate valve | cast steel gate valve | stainless steel gate valve | forged steel gate valve | ductile iron gate valve | cast iron gate valve | carbon steel gate valve | cryogenic gate valve | low temperature gate valve | high temperature gate valve | rising stem gate valve | non rising stem gate valve | pneumatic actuated gate valve | electric actuated gate valve | gear operated gate valve | hydraulic gate valve | flanged gate valve | butt weld gate valve | socket weld gate valve | threaded gate valve | npt threaded gate valve | wafer gate valve | lug type gate valve

first page 1 2 3 4 5 6 7 8 9 10 last page
[  A total of  11  pages]

Leave a message

    If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Home

Products

about

contact