-
3, For Butterfly Valve The pneumatic test of the butterfly valve is the same as the test of the globe valve. The test medium should flow into the valve from the inputting end when the test begins. Open the disc and close another end. Check the packing and other sealing parts weather it leaks after the pressure has been pumped up to the set value. Then close the disc, open the other end, check the ...
View More
-
In general, industrial valves don’t have to do a strength test in use. But repaired or corroded body and bonnet should do that. Common media used in valve pressure testing are water, oil, air, steam, nitrogen and so on. And valve pressure test methods of all kinds of industrial valves, including pneumatic, are as follows: 1.For ball valve The pneumatic test of the ball valve should be carried out ...
View More
-
1. What is the difference between Cast iron and Cast steel? The difference between Cast iron and Cast steel is their carbon content. Cast Iron with carbon content greater than 2.06% is iron; steel with carbon content between 0.02% and 2.06% is steel. 2. What is carbon steel? How many categories does it fall into? An alloy of carbon and iron (when the carbon content is between 0.02% and 2.06%) is c...
View More
-
1. What is the value of flow coefficient Kv? What is the flow coefficient Cv? Volumetric flow of water flowing between 5 ° C (40 ° F) and 40 ° C (104 ° F) through the valve to produce a pressure loss of 1 bar (14.7 psi), expressed in cubic meters per hour. Kv = Cv / 1.156 Flow coefficient Cv: It is the mass flow rate when water flows through the valve at 15.6 ° C (60 ° F) to produce 1psi, expresse...
View More
-
1. How do the pressures of ultra high pressure valves, high pressure valves, medium pressure valves, and low pressure valves differ? Ultra high pressure valve, nominal pressure PN≥100MPa; high pressure valve, nominal pressure PN10.0MPa-80.0MPa; medium pressure valve, nominal pressure PN2.5MPa-PN6.4MPa; low pressure valve PN≤1.6MPa. 2. How to distinguish the calibers of extra large caliber valves, ...
View More
-
Compared with other mechanical manufacturing processes, the valve manufacturing process has the following characteristics: A. The manufacture and inspection technology of valve rough is very complicated. The valve's casting blank is a thin-walled shell with complicated structure. Casting requires a smooth surface, casting characters clear, especially to have a dense structure, and do not allow the...
View More
-
To understand the difference between globe valve and stop check valve, we should first figure out what is a stop check valve. Stop check valve combines the functions of a general globe valve and check valve, which means besides isolating and regulating the flow rate, it can also prevent reverse flow. From the appearance, globe valve and stop check valve almost look the same. The main difference li...
View More
-
Valve actuator is a device for operating and connecting valve. The device can be driven by power source of electric power, air pressure, hydraulic pressure or other combination, and its motion process can be controlled by the stroke, torque or axial thrust. Because the actuator working characteristics and utilization rate depend on the valve type, the working specifications, and the position of th...
View More
-
These three materials of stainless steel 304, 304H and 304L are often used in valve industry. Among three, 304 is the most common one, like SS304 ball valve, SS304 gate valve, SS304 globe valve, SS304 check valve we often see. In fact, according to the content of chromium and nickel, they all belong to stainless steel 304, since they all contains 18% chromium (Cr) and 8% nickel (Ni). The ma...
View More
-
The properties of steel depend not only on the chemical composition but also on the metallographic structure. Through the process of heating, holding and cooling to get different metallographic structure and desired property is heat treatment. Common heat treatments include normalizing, quenching, tempering, and annealing. Normalizing treatment: The steel is heated to 30 ° C ~ 50 ° C above the AC3...
View More